Icona KBO 3001.BK

KBO 3001.BK Manuals/ FAQs/ Support

  • How do I descale my kettle?

    To prolong the life of your new kettle descaling should be carried out on a regular basis. The frequency required will depend on your water hardness.

    If you have particularly hard water (see the map on the right) we would recommend the kettle is descaled every month. For very soft water areas we would recommend that you descale your kettle every three months.

    Care should be taken with proprietary kettle descaler as these could damage the surface finish of the kettle. Please ensure you follow the instructions carefully.

    If you do not want to use a proprietary descaler we would recommend a solution of one part white vinegar and two parts water. Switch the kettle on, remembering to switch it off just before the boiling point. Leave the solution in the kettle for a while, dependant on the severity of the scale inside and then empty the kettle. Refill with fresh water, boil, empty and repeat this process once more. Your kettle can now be used.

    If you have missed a descale it may be worth leaving the solution overnight.

  • My kettle has what looks like a rust deposit forming inside the kettle?

    This is more than likely due to limescale build up. Limescale or staining from mineral deposits in some parts of the country can manifest itself as a brown deposit. Descaling your kettle should remove the brown deposit. To reduce limescale build up use filtered water.

  • My kettle switches off before boiling. What can I do?

    Your kettle may require descaling as a build-up of limescale deposits can affect the function of your kettle.

  • There is steam coming from the switch of the kettle when it is boiling. Is this normal?

    A slight waft of steam is normal on boiling. The switch should not be held down to sustain the boiling as this may cause a greater steam escape.

     A sensor monitors the temperature of the contents of the kettle and switches the kettle off when the correct temperature has been achieved.

  • My De’Longhi kettle is noisy. What can I do?

    All kettles regardless of manufacture will make a noise whilst boiling. The noise level is determined by the power rating, the body material and the shape. A 3KW kettle in stainless steel will always have a noisier operation than a low power plastic type. Your kettle will get noisier as it reaches boiling point. Once your kettle has boiled the noise will abate.

    If your kettle is older, descaling the kettle may reduce the noise.

  • The lid on my kettle is tight and difficult to remove. What can I do?

    The lid on your kettle should be firmly secured for safety reasons. However, if you find the lid is very difficult to remove the small tabs around the edge of the lid can be adjusted slightly to enable a better fit. This can be the case particularly where the lid has been replaced in the past.

    If your kettle is many months old, descaling the kettle may help, particularly if there is scale build-up around the lid.

  • Where can I purchase a replacement filter for my kettle?

    Spares and accessories for De’Longhi products, including many older products, are available from De’Longhi Spares via their website at http://www.4delonghi.co.uk/. Alternatively they can be contacted by calling 0844 557 6438.

    In either case please have your model number ready when ordering, which typically can be identified on the underside of the unit.

    The life of your filter can be considerably extended if you are in a hard water area by dropping it into the solution while you are descaling your kettle.

  • My kettle is spitting water from the spout

    The kettle may be overfilled which can cause spitting/over-boil.

    If the kettle has just been descaled check the solution has been completely rinsed away because this can also cause over-boil.

  • Does the browning control relate to temperature or colour of the toast?

    Browning control markings are indicative only. Setting ranges on toasters are optimised to consider all bread types used in market regions where the product is sold.

    Control graduations serve purely as a users 'visual reference' to repeat toasting characteristics for a given bread and condition. The results will also depend on the thickness and freshness of your bread.

  • How do I clean my toaster?

    Before cleaning make sure you have unplugged your toaster and let it cool down. Then slide out the crumb tray, empty it and then replace.

    Try to do this regularly depending on usage. Wipe the outside of the toaster with a damp cloth and then dry throughly.